How To Configure Local Area Network In Windows 7

1
Determine the number of computers you want to connect. The number of computers y'all're connecting will determine the blazon of network hardware you lot'll need.
- If you are connecting four or less computers, y'all'll merely need a single router, or one switch if you don't need internet.
- If you're connecting more than four computers, you'll desire a router and a switch, or just a switch if you lot don't demand cyberspace.
two
Decide your network layout. If your installing a permanent LAN solution, y'all'll want to continue cable length in mind. CAT5 Ethernet cables should not run longer than 250 feet. If you need to cover larger distances, y'all'll demand switches at regular intervals, or yous'll need to use CAT6 cables.
- You'll demand one Ethernet cablevision for each figurer you want to connect to the LAN, as well as an Ethernet cablevision to connect the router to the switch (if applicative).
Advertisement
3
Obtain the network hardware. To create a LAN, you lot'll need a router and/or a network. These pieces of hardware are the "hub" of your LAN, and all of your computers will be connected to them.
- The easiest manner to create a LAN where every computer has access to the cyberspace is to use a router, and and so add a network switch if the router doesn't take enough ports.^[1] A router will automatically assign an IP address to every computer that is connected to it.
- Switches are like to routers merely do not automatically assign IP addresses. Switches typically take many more Ethernet ports than a router has.
four
Connect your modem to the WAN port on the router. This port may be labeled "Net" instead. This will provide cyberspace admission to every computer that is connected to your LAN.
- You lot can skip this if you're setting upwardly a LAN without internet access.
- You don't demand a router at all to create a LAN, merely information technology makes things easier. If you lot simply employ a network switch, you'll need to manually assign IP addresses to each computer later connecting them.
5

Connect the switch to a LAN port on the router. If yous're using a network switch to connect more computers, connect it to one of the LAN ports on the router. You lot tin use any open port on the switch to brand the connection. When connected, the router will provide IP addresses for every computer that is connected to either device.

Advertising

1
Notice the Ethernet port on your PC. Y'all can usually find this on the back of your desktop belfry, or along the side or back of a laptop.
- Slim laptops may not have an Ethernet port, in which case yous'll need to either use a USB Ethernet adapter or connect wirelessly if your router allows it.
2

Plug one finish of an Ethernet cable into your figurer. Make sure you lot're using an Ethernet cable (RJ45), not a phone cable (RJ11).
3

Plug the other stop of the cablevision into an open LAN port. This tin be any open LAN port on either the router or the switch, depending on your LAN setup.
iv
Test out your network (router only). If y'all're using a router, your work is complete. Once all of the computers are connected to a LAN port, they will be assigned IPs automatically and will appear on the network. If you fix up your LAN for gaming, you lot should be able to beginning your LAN game and accept each computer connect.^[ii]
- If you're using a switch and no router, you'll still need to assign IP addresses to each computer.
5

Advertising

1
Right-click on your network connectedness. Y'all'll encounter this in your System Tray. If you lot are connecting your computers through a switch with no router, you'll need to assign each estimator on the network its own individual IP address. This process is handled automatically if you lot're using a router.
- Recollect of an IP address as a mailing address. Each calculator on the network needs a unique IP address so that information sent across the network reaches the correct destination.
ii

Click Open Network and Sharing Center .
3

Click the Ethernet link at the peak of the window. You'll run across this next to "Connections."
4

Click Properties .
5

Click Internet Protocol Version four (TCP/IPv4) . Brand sure you don't uncheck it, just highlight information technology.
half dozen

Click Backdrop .
7

Click the Apply the following IP address radio button.
8

Blazon 192.168.1.fifty into the IP address field.
9

Blazon 255.255.0.0 into the Subnet mask field.
10

Type 192.168.0.0 into the Default gateway field.
11

Click OK . This will save the settings for that estimator. This computer is now configured on your network with a unique IP accost.
12

Open up the Internet Protocol Version 4 properties on the next estimator. Follow the steps higher up on the 2d estimator to open up the Internet Protocol Version 4 (TCP/IPv4) Backdrop window.
13

Click the Apply the following IP address radio button.
fourteen

Blazon 192.168.1.51 into the IP address field. Find that the concluding group of numbers has incremented past one.
15

Enter the same values for Subnet mask and Default gateway . These values should be the same every bit they were on the first computer (255.255.0.0 and 192.168.0.0 respectively).
xvi

Requite each boosted calculator a unique IP. Repeat these steps for each boosted computer, incrementing the IP address by 1 each time (up to 255). The "Subnet mask" and "Default gateway" fields should be the same on each figurer.

Add New Question

Question

What is subnet mask in IP addresses?

Mitch Harris is a Consumer Technology Skillful based in the San Francisco Bay Area. Mitch runs his own Information technology Consulting company chosen Mitch the Geek, helping individuals and businesses with abode office engineering, information security, remote support, and cybersecurity compliance. Mitch earned a BS in Psychology, English, and Physics and graduated Cum Laude from Northern Arizona University.

Consumer Engineering Expert

Expert Answer

A subnet mask separates where the within of the network is and where the exterior world is.
Question

What should I practise if any website is not opening?

Mitch Harris is a Consumer Engineering science Expert based in the San Francisco Bay Area. Mitch runs his own IT Consulting company chosen Mitch the Geek, helping individuals and businesses with home part engineering, data security, remote support, and cybersecurity compliance. Mitch earned a BS in Psychology, English, and Physics and graduated Cum Laude from Northern Arizona University.

Consumer Technology Expert

Expert Answer

Brand sure that you've entered a DNS server—if you haven't, y'all'll receive an fault related to DNS and yous won't be able to access whatsoever webpages. Y'all tin enter Google's free server with "viii viii eight viii" or "8 8 4 4". If you lot use Comcast, enter "seven 5 7 five seven 5 seven 5" or "7 5 7 5 7 half-dozen 7 six".
Question

How do I connect a printer to a LAN?

Properly configure the IP of the printer, and connect it to your switch or router -- preferably a router (it will assign an IP that is uniform to your network). Make sure the port you are using is open.
Question

How can I recover my Wifi countersign?

Go to the assist desk of your provider and enter your account details and they will assist you recover it.
Question

What is the IP address?

A unique cord of numbers separated by full stops that identifies each estimator using the Cyberspace Protocol to communicate over a network.
Question

My reckoner is connected to the internet by WiFi, but cannot pull up a site. What should I do?

Try rebooting your WiFi router and your computer. If that doesn't work, effort contacting your ISP.
Question

We get an error bulletin that says "unidentified network." The cable, switch, and router are working. What should I do?

Try resetting the modem/router.
Question

I have an intermittent connection with my television. How do I stabilize information technology?

Endeavor using another cable or if you are using WiFi, try placing your router in a better location.
Question

How do I assign an IP address to my desktop?

The best manner would exist to set up a static IP address on your router. Cheque the manufacturer's website for directions specific to your device. An culling is to set a static IP through your Os. Nonetheless, this can create network collisions if another PC on your network has the aforementioned IP accost.
Question

How exercise I configure my PC to connect it to the network?

Either wireless or wired, brand sure you lot have connected it to the network past your Ethernet cable or by wifi.. 1st. A router will automatically do configurations for you every bit long as it is on the network, if not, employ a switch, and configure manually. settings>network and internet>ethernet>change adapter settings>choose the right network you are connected to>rightclick>properties>ipv4 settings>static ip addressing. make certain the default gateway are the same on all pcs, and the subnet mask, and so save and okay.

Inquire a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Near This Article

Article Summary 10

1. Plug an Ethernet cable into your PC.
2. Connect the other end of the cable to the LAN port.
three. Open your network settings.
four. Enable file and printer sharing.
5. Assign an IP address if you're not using a router.

Did this summary aid y'all?

Thank you to all authors for creating a folio that has been read 1,062,937 times.